[Research on the standard limits for vinyl chloride and trichloroethylene in the "Standards for Drinking Water Quality（GB5749-2022）" in China].

The usage of vinyl chloride and trichloroethylene in China has been increasing year by year, and they have been detected in both drinking water and environmental water, making them important environmental pollutants. Based on the latest research results on the health effects of vinyl chloride and trichloroethylene, the newly issued, "Standards for Drinking Water Quality (GB5749-2022)" in China has adjusted the standard limit of vinyl chloride from 0.005 mg/L to 0.001 mg/L and the standard limit of trichloroethylene from 0.07 mg/L to 0.02 mg/L. This article analyzed and discussed the relevant technical contents for determining the above standard limits, including the levels and exposure conditions of vinyl chloride and trichloroethylene in the water environment, health effects, derivation of safety reference values, and determination of hygiene standard limits. Suggestions were also made for the implementation of this standard.

Analysis and risk assessment of vinyl chloride emitted from aerosol products.

The objectives of this study were to develop a novel analytical method for quantifying vinyl chloride (VC) emitted from aerosol products, to provide analytical data on VC in aerosol products, and to evaluate consumer VC exposure by aerosol products. Our quantitative method involves absorbing VC into dimethyl sulfoxide and analyzing it using headspace gas chromatography/mass spectrometry. The correlation coefficients of the VC calibration curves were ≥ 0.9994 in the range of 0.16-80 µg/mL VC standard gases, which were prepared under either nitrogen or emission gases containing dimethyl ether or liquid petroleum gas. VC concentrations in these emission gases were calculated using a VC calibration curve from standard gases prepared under nitrogen; they were within ± 10% of the actual concentrations. We analyzed 39 household aerosol products; VC concentrations of 0.095, 0.098, and 0.28 µg/L were detected in three polyvinyl chloride spray paints. Consumer VC inhalation exposure level was estimated through an exposure scenario, and the hazard quotient was confirmed to be very low when comparing the exposure level with a cancer risk level of 10-5 for inhaled VC. These results suggest that the human health risk from VC in spray paint was low.

Formation and Inventory of Polychlorinated Dibenzo-p-dioxins and Dibenzofurans and Other Byproducts along Manufacturing Processes of Chlorobenzene and Chloroethylene.

Chlorinated organic chemicals are produced and used extensively worldwide, and their risks to the biology and environment are of increasing concern. However, chlorinated byproducts [e.g., polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs)] formed during the commercial manufacturing processes and present in organochlorine products are rarely reported. The knowledge on the occurrences and fate of unintentional persistent organic chemicals in the manufacturing of organochlorine chemical is necessary for accurate assessment of the risks of commercial chemicals and their production. Here, PCDD/Fs were tracked throughout chlorobenzene and chloroethylene production processes (from raw materials to final products) by target analysis. Other byproducts that can further transform into PCDD/Fs were also identified by performing non-target screening. As a result, the PCDD/F concentrations were mostly the highest in bottom residues, and the octachlorinated congeners were dominant. Alkali/water washing stages may cause the formation of oxygen-containing byproducts including PCDD/Fs and acyl-containing compounds, so more attention should be paid to these stages. PCDD/Fs were of 0.17 and 0.21-1.2 ng/mL in monochlorobenzene and chloroethylene products, respectively. Annual PCDD/F emissions (17 g toxic equivalent in 2018) during chlorobenzene and chloroethylene production were estimated using PCDD/F emission factors. The results can contribute to the improvement of PCDD/F inventories for the analyzed commercial chemicals.

Research on the standard limits for vinyl chloride and trichloroethylene in the "Standards for Drinking Water Quality（GB5749-2022）" in China / 中华预防医学杂志

The usage of vinyl chloride and trichloroethylene in China has been increasing year by year, and they have been detected in both drinking water and environmental water, making them important environmental pollutants. Based on the latest research results on the health effects of vinyl chloride and trichloroethylene, the newly issued, "Standards for Drinking Water Quality (GB5749-2022)" in China has adjusted the standard limit of vinyl chloride from 0.005 mg/L to 0.001 mg/L and the standard limit of trichloroethylene from 0.07 mg/L to 0.02 mg/L. This article analyzed and discussed the relevant technical contents for determining the above standard limits, including the levels and exposure conditions of vinyl chloride and trichloroethylene in the water environment, health effects, derivation of safety reference values, and determination of hygiene standard limits. Suggestions were also made for the implementation of this standard.

Phthalate migration and its effects on poly(vinyl chloride)-based footwear: pathways, influence of environmental conditions, and the possibility of human exposure.

The study of phthalate migration in footwear is important from an environmental viewpoint and the consumer health perspective as it remains in direct contact with the user for a long time. In this research article, the migration of phthalate, specifically di-(2-ethylhexyl) phthalate (DEHP), from the poly(vinyl chloride) (PVC) shoe sole to the attached leather insole has been studied for six months under different environmental conditions. After one month, the DEHP concentration in the PVC sole decreased by 45-58%, and that in the leather insole increased from 0.35 mg g-1 to 38-58 mg g-1. After six months, about 90% of the DEHP has been lost from the PVC sole, and that in the leather insole reached close to its initial value (value before the experiment). The migration rate depends on the environmental conditions and the presence of phthalate soluble solvents in the sole-adhesive-insole system of the footwear. The influence of DEHP migration on the physicochemical characteristics of the PVC sole and leather insole has been studied by Fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR), thermo-gravimetric analysis (TGA), and differential scanning calorimetry (DSC). The migration and emission pathways of DEHP, the influence of environmental conditions, and the possibility of human exposure to phthalate through footwear are discussed.

Detecting vinyl chloride by phytoscreening in the shallow critical zone at sites with potential human exposure.

Chlorinated ethene (CE) contaminants are widespread in groundwater, and the occurrence of vinyl chloride (VC), among others, is a well-known issue due to its mobility, persistence, and carcinogenicity. Human exposure to VC may occur through inhalation after soil vapor intrusion into buildings at sites with shallow underground contamination. Soil vapor intrusion risk is traditionally assessed through indoor air and sub-slab sampling (direct evidence) or soil gas and groundwater surveys (indirect evidence). Phytoscreening (sampling and analysis of tree trunk matrices) was proven as a cost-effective alternative technique to indirectly detect shallow underground contamination by higher chlorinated ethenes and subsequent vapor intrusion risk. However, the technique has appeared barely capable to screen for the lower chlorinated VC, likely due to its fugacity and aerobic bio-degradability, with only one literature record to date showing successful detection in trees. We applied phytoscreening at two sites with severe CE contamination nearby residential buildings caused by illegal dumping of chlorinated pitches from petrochemical productions. The two sites show variable amounts of VC in the shallow groundwater (1e2 to 1e4 µg/L), posing potential sanitary risk issues. Former soil gas surveys did not detect VC in the vadose zone. At both sites, we sampled trunk micro-cores and trunk gas from poplar trees close to contaminated piezometers in different seasons. VC was detected in several instances, disproving the shared literature assumption of the inefficacy of phytoscreening towards this compound. Factors influencing the detectability of VC and other CEs in trees were analyzed through linear regressions. Two different conceptual models were proposed to explain the effective uptake of VC by trees at the two sites, i.e., direct uptake of contaminated groundwater at the first site and uptake of VC from an anoxic vadose zone at the second site. In planta reductive dechlorination of CEs is not expected based on current literature knowledge. Thus, the detection of VC in trunks would indicate its occurrence in the shallow underground, suggesting higher screening effectiveness of phytoscreening compared to soil gas; this has implications for indirect vapor intrusion risk assessment.

The impact of vinyl chloride exposure on the health of Italian workers: an evaluation from SIREP compliance data.

The aim of the study is to investigate exposures to vinyl chloride monomer (VCM) at workplace in Italy and the related burden of diseases. Measurements data was collected from a nation-wide occupational exposure registry (SIREP, 1996-2016). Potentially exposed workers were estimated for some industrial sectors. Concurrent exposures were investigated using cluster analysis. Proportionate mortality ratios were calculated linking data to national mortality statistics (2005-2015). Overall 8,460 measurements were analyzed. Most exposures occurred in the manufacture of chemicals and plastic products. A total of 12,148 workers potentially exposed was estimated (64% male). Concurrent exposures were detected frequently (83%). An elevated proportion of deaths for liver cancer was found in male exposed workers. Although VCM is a known carcinogen for humans, there are still many exposure situations, albeit at low doses, in the chemical and plastic industries.

Distribution characteristics and health risk assessment of volatile organic compounds in the groundwater of Lanzhou City, China.

Volatile organic compounds (VOCs) typically exist in the aqueous environment due to global anthropogenic activities. The distribution and contaminated profile (or characteristics) of VOCs in the groundwater of Lanzhou, China, were investigated in this study. Groundwater samples were collected from 30 sampling points in December 2015, and a total of 17 VOCs were analyzed by purge and trap gas chromatography-mass spectrometry. Thirteen types of VOCs were detected at 29 sampling points in the study area. Of these, dichloromethane and toluene, which were found at 22 sampling points, had the highest detection frequency (73.3%), followed by benzene (66.7%), 1,2-dichloroethane (50%), and xylenes (50%). The highest average concentration among the detected VOCs was found for chloroform (5151.5 µg/L). The spatial distribution of VOC contamination in four major urban areas of Lanzhou and the variation in VOC concentration caused by land use transitions were also analyzed. The results showed that Xigu district was the most polluted area in Lanzhou, mainly due to land use for industrial proposes. On the contrary, the samples for Anning district showed lower VOC concentrations because of better groundwater quality, which is associated with the absence of manufacturing industries in this region. The health risk assessment model developed by the United States Environmental Protection Agency was employed in this study to evaluate safety for drinking water use. This study found that despite considering the volatilization of VOCs from water due to heating, six sampling points (G05 in Qilihe district; G07 and G09 in Xigu district; G16, G17, and G15 in Chengguan district) showed non-carcinogenic risks, ranging from 1.63 to 14.2, while three points (G16 in Chengguan district, and G10 and G07 in Xigu district) exhibited high carcinogenic risks for human health, ranging from 2.94 × 10-4 to 6.85 × 10-4. Trichloroethylene, tetrachloroethylene, and 1,2-dichloroethylene were identified as the dominant VOCs, presenting high non-carcinogenic risk. 1,2-dichloroethane and vinyl chloride were the primary factors for high carcinogenic risk. The high-risk areas were concentrated in Xigu and Chengguan districts, suggesting the need to alert the relevant local government departments.

Inhalation exposure to volatile organic compounds in the printing industry.

This study reports on the occupational inhalation exposure to VOCs of workers in the Kuwaiti printing industry. Using the evacuated canister methodology, we targeted 72 VOCs in three printeries and compared the concentrations to previous reports and relevant occupational exposure levels (OELs). We found that recent efforts in the printing industry to reduce VOC usage had been successful, as concentrations of key hazardous VOCs were substantially lower than anticipated. On the other hand, nearly all target VOCs were found. Non-production areas were sampled along with the offset printing areas, another strength of this study, and revealed exposures to hazardous VOCs among administers and digital printer and CTP operators. Exposure to ototoxic VOCs amounted to 1-3% of the OEL, consisting mostly of ethylbenzene, which was likely in use in two of the study printeries. Exposure to carcinogenic or probably carcinogenic VOCs was 15-20% of the OEL at four locations across the three printeries, consisting mostly of vinyl chloride and benzyl chloride. Vinyl chloride VOC was partially sourced from outdoors, but was also likely used inside the study printeries. Interestingly, concentrations of vinyl chloride were similar in most sampling locations to that of CFC-114, a CFC banned by the Montreal Protocol and not commonly used as a refrigerant. This unexpected finding suggests further study is warranted to identify the use of these VOCs in printeries. Exposure to hazardous VOCs up to nearly 50% of the OEL, consisting largely of bromoform and vinyl chloride. Bromoform was found in all the study printeries, sourced partially from outdoor air. The higher concentrations found inside the study printeries likely resulted from the use of the desalinated water for washing. This finding raises of emissions from sources other than blanket washes, and inks, etc. adding to the total VOC load in printery indoor air. Implications: Results from this study indicate that efforts to reduce worker exposure to VOCs particularly dangerous to human health in recent years have been successful, but there is still much to be done to protect workers. Exposures to ototoxic and carcinogenic VOCs were identified, among both production and non-production workers. Unexpected findings included the apparent use in printing activities of the carcinogen vinyl chloride and CFC-114, banned under the Montreal Protocol. Observed lapses in safety procedures included failure to utilize ventilation systems and closing doors between work areas, indicating management and worker education should remain a priority.

Migration of plasticizers from poly(vinyl chloride) and multilayer infusion bags using selective extraction and GC-MS.

Flexible poly(vinyl chloride) (PVC) is widely used in the pharmaceutical industry for the manufacture of medical devices (tubes, probes, bags, primary packaging, etc.). The objective of the present study was to develop a procedure to evaluate the migration potential of nine plastic additives in aqueous infusion bags (NaCl 0.9% and glucose 5%): five phthalates, one adipate, two alkylphenols, and benzophenone. Two types of materials were analyzed: (i) new and outdated plasticized PVC (containing 40% of diethylhexyl phthalate DEHP); and (ii) tri-laminate polyethylene-polyamide-polypropylene, a multilayer material presumably exempt from DEHP. In addition, we evaluated the migration of plasticizers from PVC raw materials (film and grain) under controlled conditions to compare the migration levels according to Regulation 2011/10. Solid phase extraction and liquid-liquid extraction with gas-chromatography coupled to mass spectrometry were used in all tests. The migration of DEHP in PVC grain exceeded the maximum regulated level of 5000 µg/kg, whereas the levels were much lower in films. In new PVC bags, DEHP was the only compound detected at 4.31 ±â€¯0.5 µg/L in NaCl 0.9% and 4.29 ±â€¯0.25 µg/L in glucose 5% serums, whereas the levels increased 10 times in three-year shelf-life bags. In multilayer bags, DEHP was not found but instead, two plasticizers were detected namely dibuthylphthalate (DBP) and diethylphthalate (DEP) at 0.7 ±â€¯0.1 µg/L and 4.14 ±â€¯0.6 µg/L, respectively. These plasticizers are not mentioned as additives allowed in materials intended for parenteral use (European Pharmacopoeia 8.0, 3.1.5. and 3.1.6.). Caprolactam was tentatively identified and could have stemmed from the polyamide of the multilayer composite. The levels of phthalates remained low but not negligible and might constitute a risk to public health in the case of reiterative infusions.

Using a high-organic matter biowall to treat a trichloroethylene plume at the Beaver Dam Road landfill.

Trichloroethylene (TCE) is a highly effective industrial degreasing agent and known carcinogen. It was frequently buried improperly in landfills and has subsequently become one of the most common groundwater and soil contaminants in the USA. A common strategy to remediate TCE-contaminated sites and to prevent movement of the TCE plumes into waterways is to construct biowalls which consist of biomaterials and amendments to enhance biodegradation. This approach was chosen to contain a TCE plume emanating from a closed landfill in Maryland. However, predicting the effectiveness of biowalls is often site specific. Therefore, we conducted an extensive series of batch reactor studies at 12 °C as opposed to the typical room temperature to examine biowall fill-material combinations including the effects of zero-valent iron (ZVI) and glycerol amendments. No detectable TCE was observed after several months in the laboratory study when using the unamended 4:3 mulch-to-compost combination. In the constructed biowall, this mixture reduced the upstream TCE concentration by approximately 90% and generated ethylene downstream, an indication of successful reductive dechlorination. However, the more toxic degradation product vinyl chloride (VC) was also detected downstream at levels approximately ten times greater than the maximum contaminant level. This indicates that incomplete degradation also occurred. In the laboratory, ZVI reduced VC formation. A hazard quotient was calculated for the landfill site with and without the biowall. The addition of the biowall decreased the hazard quotient by 88%.

In situ remediation of tetrachloroethylene and its intermediates in groundwater using an anaerobic/aerobic permeable reactive barrier.

Tetrachloroethylene (PCE) is among the most ubiquitous chlorinated compounds found in groundwater contamination. Its chlorinated degradation by-products remain highly toxic. In this study, an anaerobic/aerobic permeable reactive barrier system consisting of four different functional layers was designed to remediate PCE-contaminated groundwater. The first (oxygen capture) layer maintained the dissolved oxygen (DO) concentration at < 1.35 mg/L in influent supplied to the second (anaerobic) layer. The third (oxygen-releasing) layer maintained DO concentration at > 11.3 mg/L within influent supplied to the fourth (aerobic) layer. The results show that 99% of PCE was removed, mostly within the second layer (anaerobic). Furthermore, the toxic by-products trichloroethylene (TCE), dichloroethylene (DCE), and vinyl chloride (VC) were further degraded by 98, 90, and 92%, respectively, in layer 4 (aerobic). Thus, the designed anaerobic/aerobic permeable reactive barrier system could control both PCE and its degradation by-products, showing great potential as an efficient remediation alternative for the in situ treatment of PCE-contaminated groundwater.

A Luminescent 3d-4f-4d MOF Nanoprobe as a Diagnosis Platform for Human Occupational Exposure to Vinyl Chloride Carcinogen.

A luminescent nanoprobe based on a lanthanide-transition heterometallic metal-organic framework (MOF) is first designed for specific detection of urinary thiodiglycolic acid (TDGA) which is the biomarker of carcinogenic vinyl chloride monomer (VCM) and represents the internal dose of human exposure to VCM. The nanoprobe demonstrates high selectivity to TDGA with about 27.5-fold luminescence enhancement. It also displays excellent sensitivity with a detection limit as low as 89 ng·mL-1 and fast response to TDGA within 4 min, while refraining from the interference of other coexisting species in urine. Such good sensing performance enables the nanoprobe to practically monitor TDGA levels in human urine. Moreover, a portable urine dipstick based on the sensor is developed to conveniently evaluate individuals' intoxication degree of VCM. This fast, sensitive, and selective nanoprobe has promising potential to be a useful tool for point-of-care diagnosis of disease associated with VCM exposure.

Assessment of spatial variation of ambient volatile organic compound levels at a power station in Kuwait.

Twenty-four-hour integrated ambient air samples were collected in canisters at 10 locations within Kuwait's major power station: Doha West Power Station to assess the spatial distribution of volatile organic compounds (VOCs) within the perimeter of the station. A total of 30 samples, i.e., three samples per location, were collected during February and March. The samples were analyzed using a gas chromatography with flame ionization detection (GC-FID) system and following the U.S. EPA Method TO-14A with modification. The results reflected the emission activities on the site and the meteorological conditions during sampling. Generally speaking, there was a negative correlation between the ambient temperature and the VOC concentrations, which indicates the sources were local. The halogenated compounds formed the highest proportion (i.e. 50-75 %) of the total VOC concentrations at the ten locations. 1,2,4-Trichlorobenzene and Vinyl Chloride concentrations were the highest amongst the other halogenated compounds. The aromatic compounds formed the least proportion (i.e. 1-4%) of the total VOC levels at all locations with Toluene having the highest concentrations amongst the aromatic compounds at seven locations. Propene, which is a major constituent of the fuel used, was the highest amongst the aliphatic compounds. The findings of this study and other relevant work suggests the measured VOC levels were the highest over the year, nevertheless, further work is required to assess the precisely temporal variation of VOC due to change in meteorological conditions and the emission rates. IMPLICATIONS: Assessment of VOC concentrations around a power plant in Kuwait during the peak season showed halogenated compounds to be the dominant group. The calculated indoor concentrations were lower than those reported in a residential area about 12 km away.

Simulating stable carbon and chlorine isotope ratios in dissolved chlorinated groundwater pollutants with BIOCHLOR-ISO.

BIOCHLOR is a well-known simple tool for evaluating the transport of dissolved chlorinated solvents in groundwater, ideal for rapid screening and teaching. This work extends the BIOCHLOR model for the calculation of stable isotope ratios of carbon and chlorine isotopes in chloroethenes. An exact solution for the three-dimensional reactive transport of a chain of degrading compounds including sorption is provided in a spreadsheet and applied for modeling the transport of individual isotopes 12C, 13C, 35Cl, 37Cl from a constant source. The model can consider secondary isotope effects that can occur in the breaking of CCl bonds. The model is correctly reproducing results for δ13C and δ37Cl modeled by a previously published 1-D numerical model without secondary isotope effects, and is also reproducing results from a microcosm experiment with secondary chlorine isotope effects. Two applications of the model using field data from literature are further given and discussed. The new BIOCHLOR-ISO model is distributed as a spreadsheet (MS EXCEL) along with this publication.

Origin of VC-only plumes from naturally enhanced dechlorination in a peat-rich hydrogeologic setting.

The occurrence of vinyl chloride (VC) is often a main concern at sites contaminated with chlorinated solvents due to its high degree of toxicity and carcinogenicity. VC occurrence in aquifers is most often related to the degradation of higher chlorinated ethenes or ethanes and it is generally detected in plumes along with parent contaminants. However, specific combination of stratigraphic, hydrogeologic and geochemical conditions can enhance the degradation of parents and lead to the formation of plumes almost entirely composed of VC (i.e. VC-only plumes). This paper investigates the causes of VC-only plumes in the aquifers below the city of Ferrara (northern Italy) by combining multiple lines of evidence. The City of Ferrara is located on an alluvial lowland, built by the River Po, and is made up of alternating unconsolidated sandy aquifer and silt-clay aquitard deposits of fluvial origin. This region has been strongly impacted by prior industrial activities, with the occurrence of chlorinated compounds at several sites. VC-only plumes with uncertain source location were found at two contaminated sites. The source zone of a third plume composed of chloroethenes from PCE to VC was investigated for high resolution depositional facies architecture and contaminant distribution (contaminant concentration and Compound Specific Isotope Analysis - CSIA). The investigation suggested that degradation of PCE and TCE takes place during contaminant migration through peat-rich (swamp) layers related to the Holocene transgression, which locally act as a "reactor" for stimulating degradation with the accumulation of VC in the strongly reducing environment of the peat. Regional-scale stratigraphic architecture showed the ubiquitous occurrence of swamp layers at distinct stratigraphic levels in the investigated system and their apparent linkage to the in situ creation of the VC-only plumes.

Concentration effects on biotic and abiotic processes in the removal of 1,1,2-trichloroethane and vinyl chloride using carbon-amended ZVI.

A permeable reactive barrier, consisting of both zero valent iron (ZVI) and a biodegradable organic carbon, was evaluated for the remediation of 1,1,2-trichloroethane (1,1,2-TCA) contaminated groundwater. During an 888 day laboratory column study, degradation rates initially stabilized with a degradation half-life of 4.4±0.4 days. Based on the accumulation of vinyl chloride (VC) and limited production of 1,1-dichloroethene (1,1-DCE) and 1,2-dichloroethane (1,2-DCA), the dominant degradation pathway was likely abiotic dichloroelimination to form VC. Degradation of VC was not observed based on the accumulation of VC and limited ethene production. After a step reduction in the influent concentration of 1,1,2-TCA from 170±20 mg L(-1) to 39±11 mg L(-1), the degradation half-life decreased 5-fold to 0.83±0.17 days. The isotopic enrichment factor of 1,1,2-TCA also changed after the step reduction from -14.6±0.7‰ to -0.72±0.12‰, suggesting a possible change in the degradation mechanism from abiotic reductive degradation to biodegradation. Microbiological data suggested a co-culture of Desulfitobacterium and Dehalococcoides was responsible for the biodegradation of 1,1,2-TCA to ethene.

[Assessment of carcinogenic risks to workers of the main enterprises of the Irkutsk region].

The purpose of research is the assessment of the individual cancer risk (ICR) for workers of the basic occupations in key branches of industry of the Irkutsk region. There was executed the calculation of ICR levels for workers of the basic occupations of the aircraft industry, aluminum smelters and vinyl chloride production plants. The estimation of the exposure for workers was carried out according to long-term time-weighted average concentrations in the air of the working area, for the population - on annual average concentrations in the ambient air. To assess the risk that is not associated with the profession, the dose was calculated for the period of life (70 years). When calculating the toxicant doses in the working area there were used the "standard" indices ofpulmonary ventilation for adults, body weight, the work experience in the contact with carcinogens of 30 years, the number of days in the contact of 240, the duration of the working time 8 or 12 hours (in accordance with the working hours) duration. ICR for the Irkutsk population amounted of 3.08E-04, in Shelekhov - 4.8E-05, Sayansk - 1.1E-05. The amount of risk depends on the content offormaldehyde in all territories and chromium VI in cities of Irkutsk and Shelekhov. ICR for workers of basic occupations of studied plants in dozens of times are higher than for the urban population. Priority carcinogens are: chromium VI, nickel, formaldehyde, silicon dioxide -for the aircraft plant employees; 1,2-dichloretan, vinyl chloride - for the workers of vinyl chloride production plant; benzopyrene - for the aluminum smelter workers.

[Clinical and neurophysiological peculiarities of health disorders in workers in dependence on the vinyl chloride exposure load].

Results of the clinical and neurophysiological examinations of 42 workers with operating history at the chemical plant exposed to vinyl chloride (VC) are presented. The purpose of research was the identification ofpeculiarities of clinical manifestations and disorders of the functional activity of the brain in workers at the vinyl chloride production, with taking into account the exposure toxic load (ETL). There were made clinical and electroencephalographic examinations with the detection of cognitive evoked potentials (CEP) and statistical analysis of results with the use of the Mann-Whitney U-test, Fisher's F-test, calculation of Spearman's correlation coefficient. The features in clinical picture of the pathology of the nervous system were detected in the form of asthenic disorders with cognitive impairment and autonomic dysfunction syndrome. There was established the increase in the cognitive impairment rate (p = 0.03), the decline in a-EEG activity (p = 0.01) and the worsening of indices of the amplitude (p = 0.011) and latency (p = 0,05) of CEP in extremely high level of ETL in comparison with same indices in the group with moderately high ETL. In the first group there was revealed a statistically significant exceedance of the frequency of hypertension - by 1.6 times, skin diseases - by 9 times, chronic subatrophic rhino-pharyngitis by 1.4 times in comparison with cases from the second group. In the group with moderately high level of ETL there was established the statistically significant inverse correlationship between the ETL and the index of P300 amplitude from the left side (r = -0.38, p = 0.019) and in the group with extremely high level ETL - between ETL and index of the ß2 - rhythm (r = - 0.73, p = 0.0008).

Exploring a new method for the biological monitoring of plastic workers exposed to the vinyl chloride monomer.

Vinyl chloride monomer (VCM) is widely used in the production of polyvinyl chloride (PVC) plastics. VCM is recognized as a confirmed human and animal carcinogenic compound. Recent studies have reported poor health of plastic workers, even having exposure at concentrations below the permissible limit to VCM. There has not been any study regarding exposed workers to VCM in Iran. Similarly, no information exists as to the biological monitoring of such workers. The main purpose of this study was to conduct a thorough occupational and biological monitoring of Iranian plastic workers exposed to VCM.A total of 100 workers from two plastic manufacturing plants (A and B) in Tehran along with 25 unexposed workers as controls were studied. The personal monitoring of all nonsmoking workers exposed to VCM at two plastic manufacturing plants (A and B) was performed in the morning shift (8 a.m. to 4 p.m.) according to the National Institute For Occupational Safety And Health method no. 1007.Biological monitoring of workers was carried out through collection of exhaled breath of all exposed and control workers in Tedlar bags and with a subsequent analysis using gas chromatography-flame ionization detector.Not only the mean occupational exposure of workers to VCM at plant A was higher than the respective threshold limit value but also the statistical significance was higher than workers at plant B. Similarly, VCM concentration in exhaled breath of workers at plant A was also statistically significantly higher than at plant B. Correlation of occupational exposure of all workers to vinyl chloride with its concentration in exhaled breath was statistically significant.This is the first study on biological monitoring for exposed plastic workers to VCM using exhaled breath. On the basis of the results in this study, a novel method of biological monitoring of plastic workers was proposed.